生物质电厂废弃物草木灰成分分析及成形

生物质热电厂焚烧废弃物的主要成分是草木灰，其产生量大、密度小。大量草木灰不经处理会造成环境污染问题。本文首先分析草木灰的化学成分，确定草木灰的肥料特征，通过添加NH₄H₂PO₄使草木灰的pH达到国家复合肥的相关标准。选用聚天冬氨酸（30%水溶液）作为复合肥的黏结剂，应用于草木灰复合肥的成形造粒，以增加其抗压强度和肥效。研究不同烘干时间、烘干温度、聚天冬氨酸添加量对草木灰复合肥抗压强度的影响规律，通过分析植物的形态及生理指标，进而研究草木灰复合肥的肥效。结果表明：最佳烘干条件为10h、140℃，聚天冬氨酸对草木灰的抗压强度有明显的增强作用，并且草木灰与聚天冬氨酸的复配比为6g∶1mL时肥效最好。此方法解决了元素循环中断、草木灰环境污染，在运输过程中草木灰复合肥易碎，纯草木灰肥效低等问题。     

窑灰作脱硫剂的水泥窑湿法脱硫系统优化

针对水泥窑生产工艺中生料磨启停工序引起的烟气温度、二氧化硫浓度对湿法脱硫系统的影响以及杂质对湿法脱硫系统设备和浆液储罐的影响,提出了优化设计方法和运行措施,以便达到较好的烟气脱硫效果。实践表明,该工艺综合循环利用窑灰作脱硫剂,不仅可将烟气中二氧化硫能够达标排放,而且脱硫副产物石膏可作为水泥缓凝剂添加料,有较好的工程应用价值。     

循环流化床脱硫灰用于水泥生产的研究

褐煤作燃料热电厂产生的循环流化床脱硫灰应用于我公司2 500 t/d新型干法窑生产线水泥生产，由于褐煤中全硫含量偏高且波动大，由此致使脱硫过程中脱硫剂比例变化波动也大，将熟料、矿渣、脱硫灰分别用小磨粉磨后进行试验，在试验基础上，除了对该脱硫灰超细粉磨外，同时必须要解决脱硫灰的均化和f-CaO消解问题，通过技术改造使系统设备、工艺更加适合采用脱硫灰复掺技术。     

Effect of ball milling on the thermal conductivity and viscosity of Indian coal fly ash nanofluid

The present study investigates the effect of ball milling on thermal conductivity and viscosity of stable nanofluid of fly ash from Indian coal. The particle size of fly ash decreased from micron size to 89, 55.5, and 11.5 nm with reduction by 55, 90, and 434 times, respectively, due to ball milling for 30, 40, and 60 hours. The surfactant Triton X-100 was used to attain stability of 0.1% and 0.5% volume concentration of fly ash nanofluid. The samples were characterized by using scanning electron microscopy, dynamic light scattering, and zeta potential analysis. The outcome reveals that the thermal conductivity of fly ash nanofluid increases with temperature, volume concentration, and reduction in particle size. A maximum enhancement in thermal conductivity of 11.9% with 11.5-nm nanofluid sample and 5.4% with 89-nm nanofluid sample for 0.5% concentration at 60°C is observed. The viscosity of fly ash nanofluid increases with concentration and varies inversely with particle size and temperature. A difference of 1.6% in viscosity is observed between the values obtained with 11.5 and 89 nm nanofluid samples for 0.5% concentration at 30°C.     

不同粒径改性粉煤灰对磷酸根吸附性能的影响

废水排放过量的磷导致水体污染日益严重，将粉煤灰通过化学改性制备成了水化硅酸钙吸附剂，研究了改性吸附剂对磷酸根的吸附效果。利用XRD, SEM及BET比表面积等手段对粒度分级前后的吸附剂进行表征，研究不同粒级吸附剂对磷酸根的吸附性能，并考察其吸附机理。结果表明，不同粒级的吸附剂其化学成分出现了明显的偏析现象，孔隙结构也差异显著。相比其他粒径下的吸附剂颗粒，颗粒粒径在50?75 μm时，吸附剂中钙和硅含量较多，铝、铁和镁含量较低，水化硅酸钙组分含量最高，且伴有含铝的托贝莫来石晶体出现，钙离子的增加使其可以与更多的磷酸根结合形成沉淀。同时此粒径下具有较高的比表面积及孔隙度，疏松多孔的结构为钙离子提供更多活性位点。当使用粒径在50?75 μm的吸附剂吸附磷酸根时，磷的饱和吸附量可达到17.1 mg/g，比未分级的吸附剂高19.58%。     

煤粉锅炉脱硫系统中除尘器压差过高原因及解决方案

高倍率灰钙循环烟气脱硫技术在神东矿区的煤粉锅炉环保改造项目中已投入建设并成功运行,脱硫率可达95%以上。在NGD系统的运行调试期,布袋除尘器压差的数值及其上升速度均较改造前有大幅提高,影响了锅炉系统的正常运行并降低了布袋除尘器的运行效率。为了解决此问题,先分析滤料透气性降低而导致布袋除尘器压差上升的根本原因,再结合现场调研情况对NGD系统工况下的烟气含湿量、烟气温度、烟气灰浓度、除尘器本体的问题以及上游锅炉系统问题逐一进行对比和分析,并找出问题产生的各主要因素。NGD系统中布袋除尘器差压升高的原因包括多方面,为了使NGD系统的运行更加稳定,需要使除尘器适应NGD系统的工况并对系统中部分设备进行改造。在未来NGD系统的设计中,布袋除尘器需按高浓度烟气设计,且针对煤粉工业锅炉的运行、维护特性应加入对烟气中含水量的监测及对布袋除尘器的相应保护措施。     

Impact of inorganic waste fines on structure of mullite microspheres by reaction sintering

The impact of waste composition and morphology on the properties of the mullite microstructure were studied by reaction sintering two types of siliceous waste powders with calcined alum sludge. Stoichiometric mixtures of fly ash or rice husk ash with the alum sludge were shaped into mullite microspheres by droplet coagulation. The mullitization reaction was followed by HT-XRD with a distinct difference in onset temperature. The specific powder composition of fly ash (presence of primary mullite) shifted the onset temperature to higher values as compared to the rice husk ash mixture. After sintering at 1600?°C, the mullitization reaction resulted in the same yield for both samples. Although the mullite content in the microspheres was equal, distinct differences on the microstructure could be observed. Reaction sintering of the fly ash mixture resulted in lower total porosity with smaller pore sizes.     

EB-PVD alumina (Al2O3) as a top coat on 7YSZ TBCs against CMAS/VA infiltration: Deposition and reaction mechanisms

Al₂O₃ was deposited as a top coat on a standard 7YSZ layer (or layers) by means of EB-PVD technique and the corresponding morphology of the Al₂O₃/7YSZ coatings was studied in detail. This multi-layer TBC system was tested against calcium-magnesium-aluminium-silicate (CMAS) recession by performing infiltration experiments for different time intervals from 5?min to 50?h at 1250?°C using two types of synthetic CMAS compositions and Eyjafjallajökull volcanic ash (VA) from Iceland. The results show that the studied EB-PVD Al₂O₃/7YSZ coatings react quickly with CMAS or VA melt and form crystalline spinel (MgAl_2-xFe_xO₄) and anorthite (CaAl₂Si₂O₄) phases. The presence of Fe-oxide in the CMAS has been found to be key element in influencing the spinel formation which was proved to be more efficient against CMAS sealing in comparison to the Fe-free CMAS compositions. Even though a rapid crystallization was assured, shrinkage cracks in the EB-PVD alumina layer produced during the crystallization heat treatment have proven to be detrimental for the CMAS/VA infiltration resistance. To overcome these microstructural drawbacks, an additional alumina deposition method, namely reaction-bonded alumina oxide (RBAO), was applied on top of EB-PVD Al₂O_3. RBAO acts as a sacrificial layer forming stable reaction products inhibiting further infiltration.